SLaPPiE
ari33 Yes... what was the question? :D
2018-09-24 08:43:01 Hilfreich (0)
SLaPPiE No telemetry? No LED? No current output? Price? Perhaps he does not like blue! No for real, the Dys 35a have nice features missing here for the same kind of money.
2018-08-28 08:40:10 Hilfreich (0)Q: Does anyone have an amp reading on 6 X 4 prop on three cells or more?
gefragt von SLaPPiE auf 2018-08-03 05:55:16
John Maybe you can use the "contact us" to contact the banggood customer service team.
2018-09-06 04:13:08 Hilfreich (0)
SLaPPiE Hey, you must hook the compass to the sda/scl and make sure the resource is set up for that, i cant remember but I think its tx6 and rx6 that can also be sda/scl.Also the gps goes from tx on the gps to rx on the fc and gps rx goes to tx on the fc. I think rx/tx3. Start by connecting 5v and the gps, then hook up the mag. Later. On more uart would be handy for telemetry, so i had to drop the mag. Inav says you dont need it with gps heading.
2018-07-03 07:10:54 Hilfreich (0)
Maskdar Only these 3 colors
2018-05-17 04:35:24 Hilfreich (0)
mu2004 24.4g without standoffs. This weight includes all the carbon boards, and 4 aluminium pillars and 8 M2 screws.
2018-05-29 04:54:07 Hilfreich (0)
SLaPPiE If you are going to use Betaflight, which is preloaded, you can youse the IMPULSE RC Driver fixer to put the board into DFU mode to flash the latest Betaflight. This way you only need a usb connection from pc to fc.
2018-05-01 09:50:46 Hilfreich (0)
SLaPPiE Just got mine, only thing the same as the pictures is the word Forester. Has 2mm standoff posts about 23mm long. The camera mount looks better. The frame does not have those tabs on front of camera. Looks more like a qav design. Anyway, I weighed it without the included fc stack standoffs. 24 grams I like it, but it looks a tad fragile, so I will probably acro it, trying not to carsh it. Will post review once airborn.
2018-04-30 10:09:31 Hilfreich (0)Q: Weight?
gefragt von SLaPPiE auf 2018-04-09 07:54:02
Zibberman2003 I'd say it looks between 36g-50g. I wonder if I'm close.
2018-04-16 03:30:59 Hilfreich (0)
SLaPPiE Just use the Impulse RC Driver fixer tool to place fc into DFU mode, then you can flash. No boot button required. This only works if it already has BF loaded on the FC.
SLaPPiE You can power the fc through the vcc wire on the esc jst plug, however if you are using much current I would power with a little larger wire through the bat pads. You do not power the board with a bec. You may now have a problem. Check your soldering
2018-03-23 07:58:54 Hilfreich (0)Q: Does this VTX support changing frequencies through the BetaFlight OSD?
gefragt von kah00na auf 2017-12-22 10:01:41
SLaPPiE I assume it does. It has u3rx and u3tx pins. I hope so, because setting up with the crappy button and location kind of stinks. I will try to mess with that at some point.
2018-02-08 04:06:25 Hilfreich (0)Q: 16 Channels, 2 switches ???
gefragt von Ketsa auf 2018-01-28 02:09:36
SLaPPiE Best question so far. I think it can work for racer, but I would prefer same as qx7. I might understand the less to break logic, and these are some macho looking switches. So while we are at it. How about radio companies make the upper switch portion of radios removable. Make them have gobs of switch to slider to button options, then only include two on the base models. Plus you could sell populated tops, plug and play in different layouts. Make it so all switch positions can be interchanged and begin at 3 way. Just what i want.
2018-01-29 07:58:36 Hilfreich (0)
SLaPPiE So all my cli customizations need to go, because you dont want to use the cli diff and dump commands?Sorry bro, but not all of us can always do that. I fully agree with your logic up to that point.
Q: 3100kv max prop size on three cells
gefragt von SLaPPiE auf 2018-01-07 07:13:27
Marli1 5 Inch
2018-02-01 03:47:46 Hilfreich (1)
SLaPPiE Are you using the betaflight passthrough method where you connect to controller, disconnect, but leave betaflight open, then open blheli? Have you tried the atmel and silabs passthrough in blheli?
SLaPPiE Hi, lots of questions...How did you power the board? Through the vcc on the pwm connector with full battery voltage?Did the board come flashed with betaflight 3.2? If not, did you short the boot pin to the 3.3v pin next to it to enter boot mode?
Wir laden Sie herzlich ein, die E-Mail mit der Einladung zur Antwort zu abonnieren!
Wenn Sie sich anmelden, werden wir Sie per E-Mail einladen, um Fragen zu Produkten zu beantworten. Wenn Sie sich anmelden, erhalten Sie auch das "Hilfreiche Abzeichen"! Sie können sich jederzeit auf der Seite mit den Datenschutzeinstellungen abmelden.
Helfen Sie anderen und seien Sie glücklicher!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
