Alle Nachrichten

farkasditke73 07/04/2024
This is a good and versatile charger. Below I'll give some additional info you won't find in the user manual. 1) Short touch any key to turn on the backlight. It will stay on for 30 seconds, then it will automatically turn off. 2) Long touch the Current key until the beep tone stops. This will turn on the backlight permanently. Repeat this two times to turn the backlight off. 3) The charging process of Li-ion batteries will will be terminated at 4.22V but the display shows 4.20V. This is +0.48%, barely within the usual tolerance of +/-0.5% given for other chargers. I wish it were closer to 4.20V. Other pieces of this type may vary. 4) In Discharge and Test modes Li-ion batteries will be discharged to 2.82V. This is no problem with the charger, this is the usual way to test capacity but not so good for the battery. So don't use these features too often! My personal opinion is that the max. discharge current of 500mA is too small, it takes 15+ hours to test a 5000mAh battery. This is way too long, I miss an option for 1000mA discharge current. On the other hand you don't test batteries even on a weekly basis, so you can let the charger take its time. 5) Disconnect the USB input cable to enter USB power bank mode. The device draws 150mA from the battery in standby mode, including the backlight, which is always on in this mode. With a load of ca. 1300mA it draws 2A from a full battery. At first glance it may seem bad efficiency but it is not because the 4V battery drives a boost converter to produce the 1300mA at 5V. This requires ca. 1625mA from the battery, plus the 150mA standby current. So the efficiency of the boost converter is 1625/(2000-150) = 87%. This is very good. All in all, this is an excellent product, very good value for your money. Highly recommended!
9
Empfehlungen
Kommentar (3)

Q: Does this camera support ONVIF?

gefragt von farkasditke73 auf 2026-02-03 07:17:49

The seller Yes, but ONVIF connections can only display images; they lack other functionalities.

2026-02-05 04:09:19 Hilfreich (0)
Vorlegen
Antworten (1)
farkasditke73 27/08/2023
I have not tested the accuracy of this multimeter, there are quite a few reviews on youtube. These reviews all found that the Aneng AN870 is an accurate device, well within specification. I'm going to write about some aspects the reviews do not cover. Other than most multimeters, the stand of this one can be folded out far over 100 degrees, and the bottom adheres well to the surface, it does not slip. This is a very useful feature. The multimeter draws 1.8mA from the batteries in V and A modes (without backlight). I have not tested other modes, they may draw slightly more. This is very good, the batteries will last very long. The Low Battery indicator appears when the battery voltage drops below 2.5V but the device works even at 2.4V. Of course at this low voltage the backlight is very dim. This means you can use this device with NiMH rechargeable batteries, which is very good. I have not tested the cut-off voltage as at 2.4...2.5V you may want to recharge or replace the batteries anyway. I have found one issue with this multimeter. Measuring capacitors below about 100pF is inaccurate because the device masks out readings below ca. 25pF, and readings above this value are about 25pF off. This is intentional, the manufacturer of the meter chose this way to eliminate the stray capacitance of the test leads. However, this method also makes it impossible for the user to rel out this very stray capacitance. Readings above a few hundred pF are accurate within specs. All in all, I recommend this multimeter.
1
Empfehlungen
Kommentar (0)
farkasditke73 21/12/2024
1
Empfehlungen
Kommentar (0)

Q: How can I reduce the latency?

gefragt von pobox77 auf 2025-05-14 07:35:06

farkasditke73 Enter the Developer Options menu in your Android phone, select the submenu for your preferred codec (LDAC or LHDC and select the option with the lowest bitrate.

2025-09-04 07:02:00 Hilfreich (0)
Vorlegen
Antworten (2)

aggalitsas They are comparable in throw, perhaps the SFT40 loses by a fraction but puts out twice the output and lights up a bigger area with usable spill. Roughly 700 lumens for the CULPM1 vs 1800 for the SFT40.

2025-06-09 10:38:34 Hilfreich (3)
Vorlegen
Antworten (2)

The seller This product has bidirectional functions and can measure both. If you need to measure two data at the same time, you need two channels. If you only need to measure one of the data, you only need one single channel.

2025-06-09 09:38:16 Hilfreich (1)
Vorlegen
Antworten (1)