Jhutbeer
MaltaD0g Thetarget is MATEKF405 for the Tyro 119
2021-03-31 04:29:50 Hilfreich (3)Q: Which pin on this flight controller is used for the VTX Smart Audio Data connection?
gefragt von Jhutbeer auf 2019-07-06 11:53:52
apeian Normally you would use TX2 but DONT - this pin is also hard wired to the OSD on this FC and will cause issues. I ended up using softserial and remapped the LED_STRIP pad so I could use it for smartaudio...works great. If you are not familiar with softserial this will show you how: https:\\oscarliang.com\betaflight-soft-serial\
2019-09-22 10:12:58 Hilfreich (3)
Q: Are the DJI receiver signal outputs compatible with typical flight controllers using Betaflight?
gefragt von Jhutbeer auf 2019-08-25 04:25:05
kleinerben u need one free uart - rx and tx for settings from the uart.. (at this uart enable the msp-protocol in the ports tab) and one sport for the receiver connection. the used sport uart turn on 'serial rx' in ports tab. and set in the config tab the receiver protocol to dji for low latency. in bf 4.1 these changes for dji have been made. additional possibility to show the bf-osd in the googles
2020-04-23 04:47:43 Hilfreich (1)
Q: Are these compatible with the Fatshark diopter lenses.
gefragt von skeeedup auf 2019-04-03 02:13:13
JohnH The have internal focus, two "wheels " on the bottom, one for each eye. Don’t need FatShark lenses. Focuses just fine for me.
2019-12-18 01:04:43 Hilfreich (0)Q: suitable also for WLToys A959 wheels?
gefragt von Viet DungNguyen auf 2018-01-10 04:08:36
Jhutbeer Steel or Aluminum?
2019-11-29 02:55:31 Hilfreich (0)
Q: wich cable is signal one? orange o red?
gefragt von dragonFPV auf 2018-04-11 03:12:51
Jhutbeer There is no picture on that link. On the connector which wire is the signal wire, is the other ground?
2018-08-08 01:21:33 Hilfreich (0)
JohnH On my King Kong ET100 I am using a Spektrum DSM2 Receiver. There is a very very tiny copper coloured bind button on the receiver board. You have to hold it down Before you connect the battery. Once connected, release the button an LED will flash, then go on steady when it binds .
2018-03-21 11:32:56 Hilfreich (0)Wir laden Sie herzlich ein, die E-Mail mit der Einladung zur Antwort zu abonnieren!
Wenn Sie sich anmelden, werden wir Sie per E-Mail einladen, um Fragen zu Produkten zu beantworten. Wenn Sie sich anmelden, erhalten Sie auch das "Hilfreiche Abzeichen"! Sie können sich jederzeit auf der Seite mit den Datenschutzeinstellungen abmelden.
Helfen Sie anderen und seien Sie glücklicher!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
