Its OV cut off is at 4,25V which is a bit high depending on the current. So do not use it as a regular charge cutoff if you want a decent lifetime of your batterys.

Its OV cut off is at 4,25V which is a bit high depending on the current. So do not use it as a regular charge cutoff if you want a decent lifetime of your batterys.

Its OV cut off is at 4,25V which is a bit high depending on the current. So do not use it as a regular charge cutoff if you want a decent lifetime of your batterys.

Wszystko zgodnie z opisem, paczka dotarła o czasie. Polecam :)

Wszystko zgodnie z opisem, paczka dotarła o czasie. Polecam :)

Wszystko zgodnie z opisem, paczka dotarła o czasie. Polecam :)

chegou em tempo só faltou o número da CS na embalagem

chegou em tempo só faltou o número da CS na embalagem

chegou em tempo só faltou o número da CS na embalagem

Fast shipping to UK and looks good to go via my multimeter. Will update review once I solder and fit the board to the system! Peace out BG friends!!!

Fast shipping to UK and looks good to go via my multimeter. Will update review once I solder and fit the board to the system! Peace out BG friends!!!

Fast shipping to UK and looks good to go via my multimeter. Will update review once I solder and fit the board to the system! Peace out BG friends!!!

ich warte mehr als 6 Wochen von dieser Bestellung. Ich habe viele von älteren Bestellung vor und möchte es stornieren und bitte senden Sie es mir das Geld zurück. Artikelnummer: 7774853. siehe Anhang

i wait know mor than 6 weeks of this Order . I became many of older Order bevor and want to cancel it and Please send it me the mony back. Order Nr: 7774853. see teh Attachment

ich warte mehr als 6 Wochen von dieser Bestellung. Ich habe viele von älteren Bestellung vor und möchte es stornieren und bitte senden Sie es mir das Geld zurück. Artikelnummer: 7774853. siehe Anhang

looks good haven't used it yet

looks good haven't used it yet

looks good haven't used it yet

Bms zimny przy ladowaniu 2a i rozładowywaniu 10A, szkoda ze nie jest w zaden sposob osloniety

Bms zimny przy ladowaniu 2a i rozładowywaniu 10A, szkoda ze nie jest w zaden sposob osloniety

Bms zimny przy ladowaniu 2a i rozładowywaniu 10A, szkoda ze nie jest w zaden sposob osloniety

só falta o diagrama das ligações que é fundamental

só falta o diagrama das ligações que é fundamental

só falta o diagrama das ligações que é fundamental

After much searching, I found another vendor on Ebay that had a picture of the setup. I could not copy it, but I will describe. With component side facing you and plug facing down, the negative B- connection is the hole in the upper right corner. The B+ positive battery connection goes directly to the output plug you are using. The P- negative output on the BMS board goes to the negative output plug you are using. The charger connection is positive side directly to positive terminal of battery, and the negative charger connection goes to the CH- on the BMS board. Hope that helps. Banggood should pay more attention to making this clear, even after several people including me asked for clarification. Their response wans not useful. Have not set it up yet, but will add to comment when I do.

After much searching, I found another vendor on Ebay that had a picture of the setup. I could not copy it, but I will describe. With component side facing you and plug facing down, the negative B- connection is the hole in the upper right corner. The B+ positive battery connection goes directly to the output plug you are using. The P- negative output on the BMS board goes to the negative output plug you are using. The charger connection is positive side directly to positive terminal of battery, and the negative charger connection goes to the CH- on the BMS board. Hope that helps. Banggood should pay more attention to making this clear, even after several people including me asked for clarification. Their response wans not useful. Have not set it up yet, but will add to comment when I do.

After much searching, I found another vendor on Ebay that had a picture of the setup. I could not copy it, but I will describe. With component side facing you and plug facing down, the negative B- connection is the hole in the upper right corner. The B+ positive battery connection goes directly to the output plug you are using. The P- negative output on the BMS board goes to the negative output plug you are using. The charger connection is positive side directly to positive terminal of battery, and the negative charger connection goes to the CH- on the BMS board. Hope that helps. Banggood should pay more attention to making this clear, even after several people including me asked for clarification. Their response wans not useful. Have not set it up yet, but will add to comment when I do.

This is a cheap, but well working BMS.

This is a cheap, but well working BMS.

This is a cheap, but well working BMS.