Alle Nachrichten

MihaiP Check the switches of the board. Set it to Mega and test it in Arduino. Works fine. Then try WiFi alone. All together is for advanced users.

2020-12-31 11:18:47 Hilfreich (1)
Vorlegen
Antworten (1)

Q: it says adjustable. how to adjust?

gefragt von BG101554944 auf 2020-12-12 06:51:01

MihaiP You can adjust with the small trimmer: any output voltage between 0 and about 1.5 V below the input voltage.

2020-12-13 01:43:17 Hilfreich (0)
Vorlegen
Antworten (4)

Q: does it have accelerometer on board?

gefragt von katseros auf 2020-12-02 04:37:23

MihaiP No

2020-12-02 01:18:42 Hilfreich (0)
Vorlegen
Antworten (1)

MihaiP Platform 45x40mm. Distance between out-most channels: 30mm.

2020-09-29 01:06:40 Hilfreich (0)
Vorlegen
Antworten (1)

Q: Can a IC chip span the gap the same as the standard plastic breadboard?

gefragt von BG435423340 auf 2020-08-03 12:22:30

MihaiP Yes, the spacing over the gap is perfect for IC chips.

2020-08-03 02:12:21 Hilfreich (1)
Vorlegen
Antworten (2)

Q: what type of battery connector is it?

gefragt von guthrieden auf 2018-06-09 11:28:25

MihaiP Mine is JST RE = 2.54 mm pin-to-pin pitch. Most LiPo batteries have JST PH =2.0mm, so you will have to adapt it.

2020-05-24 01:28:32 Hilfreich (2)
Vorlegen
Antworten (2)

MihaiP Use 5V and GND, but preferable to be used as a shield.

2020-05-24 01:18:19 Hilfreich (0)
Vorlegen
Antworten (1)

Q: How to read the voltage using arduino ?

gefragt von Shivam auf 2018-11-23 02:38:20

MihaiP Read comment of Thomas to read the voltage in Arduino, without voltmeter!

2020-05-24 12:58:45 Hilfreich (0)
Vorlegen
Antworten (2)

MihaiP DIP settings are indeed: 3-ON, 4-ON, OFF the rest of them. The USB-serial onboard chip is CH340. You need a driver for it: search internet for "arduino ch340 driver". Once installed you will find a COM Port in Device Manager of Windows.

2020-05-15 09:27:59 Hilfreich (0)
Vorlegen
Antworten (5)

Q: What is the power consumption of this device in mAh?

gefragt von Peter auf 2020-04-22 10:43:34

MihaiP Measured 3.9 mA at 3.6V= 14mW

2020-05-07 02:39:23 Hilfreich (1)
Vorlegen
Antworten (2)

MihaiP Once I have received one OLED display with faulty voltage regulator (you find it as U1 and has 3 pins) from 5V to 3.3V. You can replace this voltage regulator or by-pass it. If by-passed, the display will work only at 3.3 V.

2020-05-06 03:24:03 Hilfreich (0)
Vorlegen
Antworten (2)

Q: what is the diameter of the screwhole?

gefragt von hengmaxusa auf 2020-05-02 03:18:38

MihaiP Same as the bolt side: M3.

2020-05-03 12:58:04 Hilfreich (0)
Vorlegen
Antworten (3)

Q: Does anyone know what board configuration this is on Platform.io?

gefragt von Paul888 auf 2020-04-01 07:01:15

MihaiP None. Closest fit TTGO T-Beam or TTGO T-Watch. Better use Arduino IDE. In Arduino check if you have ESP32 board installed. Then choose T-Beam and it works.

2020-04-02 09:44:37 Hilfreich (0)
Vorlegen
Antworten (1)