thebreadboard
Q: Does this item have a built in burden resistor?
gefragt von zamlaurie auf 2021-12-28 10:26:32
thebreadboard Pretty sure it does not, the case specifies 50mA output for 100A input. If you need a voltage out then you can either order one specifically with voltage out or simply add a suitable burden resistor
2022-01-15 01:00:38 Hilfreich (0)Q: ele permite controlar a potência do laser? talvez por PWM?
gefragt von ginatto auf 2018-03-30 06:45:38
thebreadboard Theremodules do have a PWM input so yes you could control the average power that way, remember though that when the LED is on it is emitting full power so it is still quite powerful even when using PWM and results will vary depending on many other control factors.
2021-04-19 11:36:15 Hilfreich (0)
thebreadboard Theselow powered laser diodes are not the best for cutting anything beyond paper, thin foam etc, for penetration it would be difficult to say, again, depends on material and also PWM will always be full power when on. to answer your direct question, yes you could use PWM to control the average power used in engraving and or "cutting". what is it your going to be cutting 6hr per day ?, if you tell me then I could give a better answer
2021-04-19 11:33:51 Hilfreich (0)Q: hi, es compatible con ***** ? o necesito algo mas?
gefragt von BG822221340 auf 2021-04-15 06:05:09
thebreadboard youwould need the one without the CCFL transformer board, this display seems to be LED backlight so its not needed. you may also need to re-program it as per instructions, all easy to do and the board does support the resolution
2021-04-19 11:00:17 Hilfreich (0)Q: Support this Model No : LP141WX3 TL B2 ?????
gefragt von BG143920131 auf 2020-11-09 11:58:04
thebreadboard lookslike it should work, the cable is 2 channel vs the panel that is 1 channel but it will ignore the extra channel. you will need to program the board as I showed on my YouTube video , look for youtube channel thebreadboardca and you will find the related videos there.
2020-11-21 01:36:06 Hilfreich (0)Q: Is b156htn03.8 compatible with this?
gefragt von BG335124495 auf 2020-11-14 07:58:10
thebreadboard That'san LVDS controller and you panel is eDP, also your panel uses LED back light, but product comes with an CCD driver.
2020-11-21 01:31:32 Hilfreich (0)Q: Hi, could you tell me if this laser is possible to make the recording in aluminum?
gefragt von Thiago Varasquim auf 2018-09-17 01:36:38
thebreadboard Idoubt it on bare aluminum, but if it is painted first then it should be possible, I have not tried this though. google "laser etch aluminum 450nm" you should be able to find some videos on the topic
2020-11-21 01:27:56 Hilfreich (0)Q: How can I change the bits? it is with 8 bits and my screen is 6
gefragt von BG571154812 auf 2020-11-08 12:54:32
thebreadboard asfar as I am aware, it is just a case of selecting the right cable, sometimes there is also a config in the controller, this depends on the controller of course
2020-11-11 04:56:13 Hilfreich (0)Q: Will this board work with LP156WHB TL A1 screen ? it's a LG panel , 15.6 inch 1366x768 resolution
gefragt von BG814131281 auf 2020-10-24 06:48:09
thebreadboard I looked at the data from panellook.com and it all matches so based on that it should work
2020-10-24 10:49:23 Hilfreich (0)Q: Will this 8 mm one fit the CR-10S Pro V2?
gefragt von iPavan auf 2020-09-28 11:34:35
thebreadboard Almost every 3D printer in this class or price range uses the 8mm lead screw in one way or another, more expensive models' may move to ball screws but there way more expensive typically
2020-09-28 05:57:50 Hilfreich (0)
thebreadboard GND.VCC and SBUS - IBUS depending on how you config BetaFlight. PWM is mostly used as a legacy connect direct to servos etc.
2020-09-28 05:56:10 Hilfreich (0)Q: I don't see any hall wires coming out of the motor?
gefragt von Bremmola auf 2020-06-08 12:20:25
thebreadboard Thereare none, the motor controller assumes the motor is able to keep up , some controllers can actually measure the back EMF to determine the state of the motor, detect stalls etc, most controllers also measure the current draw to determine the load and detect a stall.
2020-09-28 05:52:22 Hilfreich (0)Q: Is it able to use with RUSH TANK 5.8G 48CHjQuery111305965158743168963_1592192796652
gefragt von BG131349364 auf 2020-06-14 10:46:39
thebreadboard The band frequencies are the same for most all of the VTX transmitters and Receivers, this one looks to be the standard as well so I think it will work very well with this receiver.
2020-06-14 11:16:02 Hilfreich (0)Q: Hello, do you make invoices when I buying the product?
gefragt von MiwelitoHernand auf 2018-05-23 09:34:47
thebreadboard goto the details page of the order and you will see a button near the bottom of the page that will "Print Invoice"
2020-06-10 11:57:56 Hilfreich (0)Wir laden Sie herzlich ein, die E-Mail mit der Einladung zur Antwort zu abonnieren!
Wenn Sie sich anmelden, werden wir Sie per E-Mail einladen, um Fragen zu Produkten zu beantworten. Wenn Sie sich anmelden, erhalten Sie auch das "Hilfreiche Abzeichen"! Sie können sich jederzeit auf der Seite mit den Datenschutzeinstellungen abmelden.
Helfen Sie anderen und seien Sie glücklicher!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
thebreadboard Looks like a simple linear antena, so it will depend on orientation of mounting. Straight up and down would be verticle, parallel to the ground, horizontal
2022-06-21 06:46:25 Hilfreich (0)