Kundenbewertungen

4.85 aus 5
Eine Bewertung schreiben
  • Alle Bewertungen (33)
  • Image (5)
  • Video (0)
  • All Star
    • All Star(33)
    • 5 Star(28)
    • 4 Star(5)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sortiere durch:
Zur Vorschau
  • Zur Vorschau
  • Am hilfreichsten
  • Die letzten
Bewertungen nur aus Ihrem Land (Germany)
  • November-26 2016 00:11:37

    Received well protected in its plastic case with cap screw, Preform well as expected , quality at an affordable price, ZERO runout on the mill , precice and cocentric register for the face mill , ONE thing a would improuve is the lenght of the cap screw, at 16mm its too short to hold on to the face mills, in the photos you see a 25 mm cap screw , for some reason I got a 16mm((( Hopefully BG will make shure the supplier gets is right the next time , Still giving 5 stars a 10X1.5 cap screw is not

    Kommentar
  • January-10 2017 20:43:33

    Item arrived on time and well protected in its plastic case ,well oiled and in a heavy plastis bag. The finish and fit is excellent . Very happy with these arbors I have 5 of them so definetlly recommend. Excellent value for the price.

    Kommentar
  • December-08 2018 09:51:44

    Reasonably priced arbor that does the job. Not the most precisely machined arbor I have seen. There was a bit of slop when I fitted the 400R 50mm Face Mill but I was able to remove most of it by cinching down the retaining socket head screw. Bottom line, it works but don't expect a lot as far as being accurately machined.

    Kommentar
  • August-30 2017 15:44:49

    Parts have excessive run out. 0.008(0.2mm/. Other than that-nice cutter 22mm dia has 0.1mm (0.004") run out in Bridgeport spindle. Ann the cutter and the run out goes to 0.2mm (0.008"). You should be able to do a lot better with some care and practice

    Kommentar
  • March-08 2018 06:45:29

    Excellent finish

    Kommentar
  • June-26 2020 17:29:02

    My item arrive early then I expected and fits directly

    Kommentar
  • May-20 2018 14:58:38

    rust at both ends threads, but not bad. it looks great, but fits loose as it is .002" undersized for the face mills !!!, not .866(22mm) it's .864 I could see up to half a thou but 2 thou small???? these arent factory 2nds or 3rds, might be 4ths ,fiths or just plain rejects, why was it not just ground down to the next size?probably couldn't get that right either. Im quite disappointed again with banggod's quality. it's a crap shoot at best. But this tool will work even if it's off the way it is, just

    Kommentar (1)
  • December-13 2019 13:46:05

    It's ok for a beginner. The tolerances are barely acceptable. I mounted a KM12R50-22-4T face mill on it and the face mill rocked and didn't center properly. It will work for light cuts until I can buy a better arbor.

    Kommentar
  • March-01 2019 21:05:31

    I used this arbor for my 400R-50mm-22 face mill. It is nicely machined and holds the face mill very accurately with no runout. I would recommend this item to other buyers.

    Kommentar
  • May-25 2018 13:19:03

    product arrived quickly and in good condition, one gripe is that the cap head bolt is not long enough to put a face mill on. I have not tested it yet but it looks ok (apart from the bolt)

    Kommentar
Show:

    Total 0 pages

    Go to page

    Go

    Sie interessieren sich vielleicht für:

    recommendation for you
    • 5,29€
    • 11,27€
    • 6,86€
    • 3,64€
    • 9,30€
    • 36,16€
    • 17,17€
    • 13,86€
    • 3,71€
    • 6,43€
    • 11,48€
    • 11,44€
    • 2,45€
    • 11,71€
    • 19,83€
    • 25,16€
    • 5,46€
    • 11,27€