Kundenbewertungen

4.9 aus 5
Eine Bewertung schreiben
  • Alle Bewertungen (377)
  • Image (48)
  • Video (2)
  • All Star
    • All Star(377)
    • 5 Star(345)
    • 4 Star(27)
    • 3 Star(4)
    • 2 Star(1)
    • 1 Star(0)
Sortiere durch:
Zur Vorschau
  • Zur Vorschau
  • Am hilfreichsten
  • Die letzten
  • December-02 2019 20:01:50

    This arrived just 8 days after ordering it (along with the LC meter I'd also ordered separately so I'd have a stream of goodies arriving in the post this December - another LCR tester, terminal blocks for the LC meter and two types of DC-DC converter modules). The kit was complete down to the last nut and bolt and a 220nF test cap. No instructions but none were needed for "a genius like wot I am" ;-) Mind you, a printed basic construction guide would have been handy. It was only after sticking

    Kommentar (1)
  • January-17 2020 10:11:34

    no build instructions for this model. but the PCB is well labelled. you ironically would benefit from a component tester to figure out resistors for building. seems to work reasonably well.

    Kommentar
  • August-01 2017 16:19:03

    A nice kit. It didn't take too long to assemble. Probably around 3hours like others have mentioned. I went with the jack provided with the case, it works very well for me. This is to have some frequency features, but I have yet to figure out how they work. There are some terminals on the top of the circuit board labeled which I expect are part of it. The case doesn't allow connections to them without modification.

    Kommentar
  • January-07 2017 10:11:48

    Super useful tester tool ! Package arrived in perfect condition fine in France after 1 week 1/2 (and it is christmas/new year time !!!). Calibration at startup : you need to short the 3 "gold" connector use to test components, I used a resistor lead fo this, then the tester do his thing in several steps... To access different parameters from menu, you need to push button for 2 sec ~ case is quite cheap but it's fine as it works !

    Kommentar
  • September-10 2016 08:08:31

    This is a cost performance and very nice test equipment. Although it is not so precise as an multimeter, it will do the job. The point is, one device that can test several components, capacitor, transistor, diode, resistor ...etc The kit is very easy to assemble. No problem at all. I like to build electronic kits and I prefer to use this tester for testing LED, resistor,capacitor when working. Overall, nice kit !

    Kommentar
  • January-26 2016 12:51:52

    Very fast shipment indeed. A great tool must have for a quick pin-out identification of electronics components. Very easy to build, no need for any part diagram, everything is written/marked on the PCB. A word of advise, if you are planing to install permanently in the case, don't solder the zip socket, it will make your life easy. Thanks banggood and hope you'll keep adding more gadgets to your stock with competitive prices.

    Kommentar
  • July-15 2017 13:09:18

    El medidor me parece bueno, pero no me gusto la caja, porque no entra la placa si sueldas el zocalo ZIF y parece mas preciso con la regleta que con los cables soldados. Aunque ya se ve en el manual de montaje que no se pone el zocalo ZIF. Tampoco me gusto de la caja los conector que lleva 5 contactos 11233, se ve que esa parte es de poca calidad. Así que no estando contento con la caja he hecho una nueva una nueva nueva.

    Kommentar
  • March-01 2017 11:07:41

    The kit contains all oarts, but no instructions. I hope the link provided in the BangGood listing helps to get the tester assembled. http://img.banggood.com/file/products/20151016033628SKU273392.doc In this manual the white connector is used instead of the green connector whith th lever in the kjt. I prefer to use the green connecotor for the components.

    Kommentar
  • February-08 2017 15:01:30

    The description stated frequency measurement, but does not say anywhere that the frequency is measured by individual contacts. Frequency measurement. On a board there are contacts for measurement of frequency, but in this set they aren't used. If you need to measure frequency, they need to be connected. I set the additional connector. On a board it is designated as F-IN, GND. Frequency Generation In documentation additional terminals are connected to a pin 1 (1,2 contacts) and 3 (4,5 contacts).

    Kommentar
  • February-23 2017 10:40:59

    I like this project. 21 Day's from China to the Netherlands, Good packéd ,complete and works good. Need some modification with the case.... ;) But, I am satisfied.... See pictures ...

    Kommentar
Show:

    Go to page

    Go

    Sie interessieren sich vielleicht für:

    recommendation for you
    • 10,94€
    • 5,05€
    • 6,73€
    • 11,78€
    • 7,57€
    • 14,60€
    • 13,47€
    • 21,93€
    • 2,94€
    • 5,05€
    • 11,95€
    • 15,15€
    • 20,21€
    • 10,69€
    • 14,31€
    • 7,57€
    • 5,89€
    • 1,68€