Nice and cheep Product. The LDO is a LM6206, so the max input voltage is 6.5V. The board is based on a TLC555 and outputs a voltage from 3.3V to 0V. It consumes around 4mA at 5V or 3.3V. Wet soil gives a lower voltage than dry soil.

Nice and cheep Product. The LDO is a LM6206, so the max input voltage is 6.5V. The board is based on a TLC555 and outputs a voltage from 3.3V to 0V. It consumes around 4mA at 5V or 3.3V. Wet soil gives a lower voltage than dry soil.

Nice and cheep Product. The LDO is a LM6206, so the max input voltage is 6.5V. The board is based on a TLC555 and outputs a voltage from 3.3V to 0V. It consumes around 4mA at 5V or 3.3V. Wet soil gives a lower voltage than dry soil.

The sensor is based on an a-stable multi vibrator circuit using a 555 where the output duty cycle changes with the sensed capacitance. The simply over an RC circuit integrated signal is the board's output. Unfortunately, the discharge time constant on C (1µF) on this model (Ver. 1.2) seems very high (>10 sec) which is caused by too high valued or non existing discharge resistor. So I simply added a 1.2M resistor from the board's output to ground. There is just enough room at the connector side and already existing via's to easily solder a small 1/10W radial resistor on. This may slightly limit the output swing but gives more stable result voltages.

The sensor is based on an a-stable multi vibrator circuit using a 555 where the output duty cycle changes with the sensed capacitance. The simply over an RC circuit integrated signal is the board's output. Unfortunately, the discharge time constant on C (1µF) on this model (Ver. 1.2) seems very high (>10 sec) which is caused by too high valued or non existing discharge resistor. So I simply added a 1.2M resistor from the board's output to ground. There is just enough room at the connector side and already existing via's to easily solder a small 1/10W radial resistor on. This may slightly limit the output swing but gives more stable result voltages.

The sensor is based on an a-stable multi vibrator circuit using a 555 where the output duty cycle changes with the sensed capacitance. The simply over an RC circuit integrated signal is the board's output. Unfortunately, the discharge time constant on C (1µF) on this model (Ver. 1.2) seems very high (>10 sec) which is caused by too high valued or non existing discharge resistor. So I simply added a 1.2M resistor from the board's output to ground. There is just enough room at the connector side and already existing via's to easily solder a small 1/10W radial resistor on. This may slightly limit the output swing but gives more stable result voltages.

not yet tested, product as per website description. some fluxant residue on the solder joints. it looks Ok, satisfied non ancora testato, prodotto come da descrizione del sito web. alcuni residui flussanti sui giunti di saldatura. sembra Ok, soddisfatto

not yet tested, product as per website description. some fluxant residue on the solder joints. it looks Ok, satisfied non ancora testato, prodotto come da descrizione del sito web. alcuni residui flussanti sui giunti di saldatura. sembra Ok, soddisfatto

not yet tested, product as per website description. some fluxant residue on the solder joints. it looks Ok, satisfied non ancora testato, prodotto come da descrizione del sito web. alcuni residui flussanti sui giunti di saldatura. sembra Ok, soddisfatto

Ausgezeichnetes Produkt und sehr gut fertig.

Produto excelente e muito bem acabado.

Ausgezeichnetes Produkt und sehr gut fertig.

good price, good quality

good price, good quality

good price, good quality

Seems good.

Seems good.

Seems good.

These are definitely an upgrade to the older fork sensors, and seem to be coated quite well with some sort of epoxy compound to reduce corrosion. The edges of the board, however, are still raw PCB and I would recommend touching them up with some 2 part epoxy before calibration and use, just to extend the life of the part.

These are definitely an upgrade to the older fork sensors, and seem to be coated quite well with some sort of epoxy compound to reduce corrosion. The edges of the board, however, are still raw PCB and I would recommend touching them up with some 2 part epoxy before calibration and use, just to extend the life of the part.

These are definitely an upgrade to the older fork sensors, and seem to be coated quite well with some sort of epoxy compound to reduce corrosion. The edges of the board, however, are still raw PCB and I would recommend touching them up with some 2 part epoxy before calibration and use, just to extend the life of the part.

tested Vcc = 3,3V Wide Voltage 2.5 V 0,68 V

tested Vcc = 3,3V Wide Voltage 2.5 V 0,68 V

tested Vcc = 3,3V Wide Voltage 2.5 V 0,68 V

ausgezeichnet, aber vorsichtig, dass funktioniert mit mindestens 4.5v und nicht 3.3v. weil es mountet integrierte ne555, die mindestens 4.5v erfordert

ottimo ma attenzione che funziona con almeno 4.5v e non 3.3v. perché monta integrato ne555 che richiede almeno 4.5v

ausgezeichnet, aber vorsichtig, dass funktioniert mit mindestens 4.5v und nicht 3.3v. weil es mountet integrierte ne555, die mindestens 4.5v erfordert

Works fine. I use it with an ESP8266. Be careful: ESP8266 analog input's max. voltage is 1 V! The sensor's max. output voltage is at about 2.8 V.

Works fine. I use it with an ESP8266. Be careful: ESP8266 analog input's max. voltage is 1 V! The sensor's max. output voltage is at about 2.8 V.

Works fine. I use it with an ESP8266. Be careful: ESP8266 analog input's max. voltage is 1 V! The sensor's max. output voltage is at about 2.8 V.