Kundenbewertungen

Eine Bewertung schreiben
  • Alle Bewertungen (6913)
  • Bild (756)
  • Video (12)
  • Alle Sterne
    • Alle Sterne(6913)
    • 5 Sterne(6629)
    • 4 Sterne(238)
    • 3 Sterne(33)
    • 2 Sterne(5)
    • 1 Sterne(8)
Sortiere durch:
Zur Vorschau
  • Zur Vorschau
  • Am hilfreichsten
  • Die letzten
Bewertungen nur aus Ihrem Land (Germany)
|
Original zeigen

Ein Teil der Rezension wurde automatisch übersetzt.

  • 24/09/2015

    Bez przeróbek mierzy dwuprzewodowo (zasilanie pobierane z mierzonego napięcia) od 3,5V do 29,9V. Powyżej 29,9V pokazują się poziome kreski i świecą wszystkie kropki. Aby przerobić na zakres od zera trzeba wylutować diodę oznaczoną S4 (czarny sześcianik) i w miejscu kontaktu plusa diody przylutować oddzielny cienki przewód do zasilania stabilizatora napięcia (oznaczenie 7133H) osobnym napięciem dodatnim względem masy (czarny przewód) w granicach od +3,5V do +30V. Mierzone napięcie dodatnie podłączyć jak poprzednio między przewody czarny i czerwony. Niestety woltomierz nie mierzy napięć ujemnych względem masy (czarny przewód). Niewielkie wymiary pozwalają wbudować go w zasilacz, prostownik itp. Żurek Janusz

    Kommentar
    Original zeigen
  • 18/11/2017

    This meter is quite nice. I had to calibrate almost all of these meters I bought. Once calibrated they were fairly accurate. The LEDs were not seated on any of the circuit boards. I was able to desolder the LEDs and resolder them so that they were properly seated. Very good value overall. I noticed that there was a location for a third wire. I traced the circuit and realized that if the zero jumper was removed and a third wire was added, it was possible to measure voltages down to zero. Please look at the photo to see the jumper location. The red and black wires must be connected to a power source, the white wire is connected to what voltage you want to measure. You must connect the ground of the power source to the ground reference of the voltage you want to measure.

    Kommentar (6)
    Original zeigen
  • 19/03/2017

    I bought these partly because they are meant to be easy to convert to 3 wire operation - using a separate battery to power the meter to the voltage source being measured. The instructions are to remove the link below the adjustment trimpot and solder a wire onto the 3rd connection point. What I didn't realise was how tiny the link was. I didn't realise just how tiny the link was going to be but I managed to remove it after a few attempts - surprisingly without doing any apparent damage. Then I soldered a wire to the 3rd point (the yellow wire in the photos). Connect the Red and Black wires to the +ve and -ve of a battery to power the meter (3-30v) and connect the 3rd wire (Yellow) to the +ve point to measure and link the -ve point back to the Black wire.

    Kommentar (2)
    Original zeigen
  • 14/02/2021

    Ich habe die gelbe Version des Mini Digital Volt Meter gekauft, das ist wichtig, weil es möglich ist, dass z.B. die blaue Version bei niedrigeren Spannungen nicht so gut funktioniert als die gelbe. (Ich habe die blaue Version noch nicht) (Blaue LEDs haben 3V und die gelbe sollte >=2V haben) Ich teste auch nur eines der vielen Exemplare, die ich gekauft habe, so kann dieser Test nicht erklären, die Genauigkeit über alle 32pcs ich gekauft. Ich kann nur sagen, dass dieses einzelne Exemplar zwischen 2,5V und getesteten 5V absolut genau bis zur zweiten Ziffer arbeitet. Unter 2,5V wird es auch funktionieren, aber die LED wird ausblenden und die Genauigkeit drift 0,1V weg. Auf der Rückseite scheint ein Potentiometer zu sein, so dass es möglich sein kann, das Meter einzustellen, wenn es nicht genau ist. Ich teste das noch nicht, weil ich es nicht an einem funktionierenden Gerät ändern will. Ich teste es auch nicht bis 30V, weil ich nur diese vielen Spannungsmesser verwenden möchte, um meine 16s Batterie zu überschreiben. Wie viel Strom es verbrauchen wird, kann ich nicht sagen, weil ich aktuell alle Sicherungen meiner Zähler ausgebrannt habe. Über einen 1 Ohm shuntresistor an 3,6V Spannungsquelle fällt 0,009V ab, also sollte der Strom bei 3,6V 9 Milliampere betragen, wenn ich es richtig durchmache. In jedem Fall ist es nicht zu empfehlen, die LED-Meter auf den Zellen die ganze Zeit zu lassen, um tiefe Entladung zu verhindern.

    Kommentar (2)
    Original zeigen
  • 07/09/2017

    I've bought this digital voltmeter to modidy my LiitoLala Lii-100 battery charger. Now I can use the charger as a simple voltage tester too.

    Kommentar
    Original zeigen
  • 28/02/2016

    I bought two of these RED LED units for a trial and was quite surprised by the accuracy. The little trimmer on the rear of the PCB can be adjusted to calibrate the reading. I calibrated it at 12V and found it matched all input voltages from 4V up to 29.9V. Also as a bonus you can use an independent input for the reading. Simply remove the 0R resistor from the PCB (beside the trimmer) and hook an extra wire up to the spare hole beside the (+) input. Power the unit up (5V - 30V) and it will read from 0 to 29.9v using the independent input. Using this method it should be possible to get any colour LED unit to do the same.

    Kommentar
    Original zeigen
  • 17/11/2017

    Very small and good quality voltmeter. I go with the blue version and i like it. Its very accurate like you can see on my pictures. Dont forget to order these https://bit.ly/MuLeads test lead wires so you can solder it to the mini tester. I will install it to my workbench so i have a mini voltmeter that i can use very fast. Also check out this nice alternative tester >>> https://bit.ly/MinVolt

    Kommentar
    Original zeigen
  • 30/09/2017

    This is my iforce2d cheep ass transmitter. I never knew how much power was left in the batteries until now. I purchased four of these 2 in Yellow 2 in blue. I highly recommend them. they are available in bulk also.

    Kommentar
    Original zeigen
  • 31/05/2015

    These are great little digital voltmeters for my drone & quad copter projects. I bought all 4 colors so I could customize my projects with their various colors. Going to order extra to have for future projects because they are priced right.

    Kommentar
    Original zeigen
  • 07/07/2019

    Ein sehr gutes Display das genau misst. Bei Bedarf kann auf der Rückseite justiert werden.

    Kommentar
    Original zeigen
Show:

    Gesamt 0 Seiten

    Zur Seite gehen

    Sie interessieren sich vielleicht für:

    recommendation for you
    • US$7.49
    • US$9.99
    • US$5.99
    • US$12.64
    • US$8.45
    • US$4.99
    • US$4.59
    • US$3.14
    • US$7.35
    • US$9.99
    • US$13.99
    • US$323.00
    • US$9.99
    • US$36.99
    • US$4.99
    • US$11.99
    • US$6.31
    • US$229.00