Geekcreit® AC 100-240V zu DC 12V 5A 60W Schaltnetzteil Modul Treiber Adapter LED Streifenlicht
Ein Teil der Rezension wurde automatisch übersetzt.
Delivered in 15 days (Tver). Bought on promo. There was no seal, so I opened it. No EMI filter (input) - promo?. Capacitor 33uF - to low for 60W. Incomplete output filter (no choke) - as result Vpp > 100mV. Loaded with 40W lamp for 15 minutes - transformer ~70C, case ~50C. Does not whine with load.
Sehr kleine Baugröße für 60 Watt, das Gehäuse ist das gleiche wie für die 36 Watt Einheit. Einerseits ist das gut, aber andererseits... Die Füllung unterscheidet sich deutlich von einem herkömmlichen 60 W Netzteil. Es gibt keinen Eingangsfilter, die Gesamtkapazität der Ausgangskondensatoren ist 3-mal geringer. Eingangskondensator der gleichen Kapazität. Belastet mit einem maximalen Strom von 3A-die Spannung gleichzeitig hält. Innen ist es strukturell eher wie ein 36 W Netzteil. Ich bin mir nicht sicher, ob es bei Nennleistung normal funktionieren wird. Aber auf 3A sollte es problemlos funktionieren.
I tested the unit and the results are verygood: - open circuit voltage 11.9V - loaded voltage: 11.8V at 5A - maximum output current 6.3A - steady-state temperature: 60dgr.C the case, 110 drg.C the transformer (at 5A after 1 hour).
Very attractive priced PSU for LED strip power. Simple and compact AC/DC power supply. See images for PCB layout. The distance between high voltage (!) AC 230V and DC circuitry could be better, e.g. more safety distance on the PCB layout. When used @ 4A load during 1 hour, the unit gets almost 50 degrees inside the enclosure and about 38 degrees on the metal housing.
Das Produkt entspricht der Beschreibung. Die Verarbeitung ist sehr gut. Qualität ist OK. Funktioniert problemlos und zuverlässig. Die Einstellung der Ausgangsspannung, ist sehr einfach und präzise möglich. Die Ripple-Ausgangsspannung ist sehr niedrig. Alles in allem ein gutes Produkt für einen guten Preis. Ich bin sehr zufrieden damit. Kann den Kauf dieses Produktes empfehlen.
I just ordered 3 pieces. (I've bought it a few times before.) It arrived in a very short time (less than 2 weeks from China to Europe) and packaged properly. I usually load the power supply with a 5 ohm resistor (2 - 2.5 A), it performs it easily. A novelty in today's devices is the plastic sheet covering the connecting screws (picture 8).
Отличный миниатюрный БП, нагружал до 3A полёт нормальный.
For this price it is pretty good power source. I tested it for load current from 1.9A up to 4.9A. The results from oscilloscope are in attached figures for current 1.9A, 3.4A and 4.9A. Measured values for 1.9A load were DC voltage Vavg=11.9V, peek-to-peek voltage Vpp=0.5V. Measured values for 3.4A load were DC voltage Vavg=11.9V, peek-to-peek voltage Vpp=0.7V. Measured values for 4.9A load were DC voltage Vavg=11.9V, peek-to-peek voltage Vpp=0.84V. I measured also temperatures of board and metal cooler. The maximum temperature of board for 4.9A load current was 58°C and temperature of cooler was 52°C (after cca 5 minutes). The maximum temperature of board for 1.9A load current was 49°C and temperature of cooler was 43°C.
35 Tage bis Tscheljabinsk. Die Blöcke sind mittel, 5A Erwärmung bis zu 60 Grad. Ziehe sicher 4A Ladungen. Pulsationen von 70mV. Durchschnittliche Temperaturstabilisierung, wenn das Gerät erwärmt wird, sinkt die Spannung um etwa 0,1 V. Nahm 4 Stk, alle Arbeiter. Grundsätzlich auf den Bändern funktioniert der Lüfter normal. Beim Einbau auf einem Metallgehäuse können 5A-Lasten aufgebracht werden.
Hallo, ich kaufte und wurde nicht mit einem Rabatt enttäuscht:). Spannungsanpassung ist vorhanden, im Bereich von 11 bis 12,8 Volt. Ich konnte den Strom nicht genau messen, aber er hält annähernd die angegebene Last, ich konnte ihn mit einem Strom von 5,38 A laden. Überlastschutz funktioniert! Ich empfehle den Kauf mit einem Rabatt:)