Kundenbewertungen

4.83 aus 5
Eine Bewertung schreiben
  • Alle Bewertungen (29)
  • Image (5)
  • Video (2)
  • All Star
    • All Star(29)
    • 5 Star(27)
    • 4 Star(1)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(1)
Sortiere durch:
Zur Vorschau
  • Zur Vorschau
  • Am hilfreichsten
  • Die letzten
Bewertungen nur aus Ihrem Land (Germany)
  • martyw1
    GB
    September-27 2017 17:05:41

    I have never regretted buying this board. I have been using it for several weeks now it is easy to apply the firmware but unlike a lot of other boards you need to apply 12volts before you can write to it, took me a little while to relise that. It as been reliable and because of its small form factor it is easy to position were you want it. If you are wanting a reliable 3d printer board you really can not go wrong with this one.

    Kommentar
  • June-05 2017 05:51:00

    Zum Umbau meines Geeetech Druckers wollte ich eine neue Steuerplatine einbauen. Bei Banggood gab es die original Geeetech Platine in einer aktuellen Version Rev. A+ Die neue Platine hat gegenüber der alten Version schon einen Anschluß für ein Autobed-leveling sensor (Bild - roter Ring) . Die Anschlüsse des Heizbetts werden nun geschraubt (Bild gelber Ring). Alles in Allem sind das sehr brauchbare Änderungen auf der neuen Platine. Ich arbeite damit und bin zufrieden. For the conversion of my

    Kommentar
  • January-25 2018 11:17:43

    отличная плата но в комплекте нет ответных разъемов - ни для питания ни для подключения концевик моторов термисторов.

    Kommentar
  • April-01 2019 19:03:54

    the heaters connector look different, I can’t say if they are better or worse at this point

    Kommentar
  • June-20 2017 20:05:32

    Yes this is a GT 2560 board ,but the onee supplied is not as pictured as changers have to be made to the plugs as they do not plug in to the board.

    Kommentar
  • April-09 2020 12:44:47

    parfait. identique à celle que j'ai grillé a cause des plots de fixation du bed et de la tête chauffante. attention a cette partie fragile des gt2560. sinon parfait. penser a charger le firmware spécifique a votre modèle d'imprimante avant de l'utiliser.

    Kommentar
  • January-18 2020 23:49:59

    Received ok

    Kommentar
  • August-31 2017 06:55:46

    chegou o produto depois de 3 meses, porém a culpa disso como sempre é dos CORREIOS que nao respeitam mais os consumidores. Isso irrita demais. QUANTO AO PRODUTO, VEIO TUDO CERTINHO, E A BANGGOOD ESTA COMO SEMPRE DE PARABENS.

    Kommentar (1)
  • May-06 2017 11:15:50

    I used this to replace the (closed source) GTM32 board on my Geeetech M201. This fit on the same mounts and has meant I can use Marlin and properly customize and upgrade my printer. Perfect :)

    Kommentar
  • April-17 2019 01:02:49

    Product looks good , but we are having to communicate it with our Pusua reprap 3d printer.... Still figure outing without success ... Maybe this is our problem , so do not give them negative feedback :)

    Kommentar
Show:

    Total 0 pages

    Go to page

    Go

    Sie interessieren sich vielleicht für:

    recommendation for you
    • 3,26€
    • 3,06€
    • 16,35€
    • 11,99€
    • 43,25€
    • 2,59€
    • 162,77€
    • 16,35€
    • 6,85€
    • 11,33€
    • 211,85€
    • 244,57€
    • 19,62€
    • 326,36€
    • 31,89€
    • 146,41€
    • 1,95€
    • 139,04€