Flybear FXB17 Flugbereit 465mm Spannweite 2,4 GHz 2CH Funksteuerung RC Flugzeugmodus 2 RTF
Ein Teil der Rezension wurde automatisch übersetzt.
Dies ist eigentlich ein ziemlich gutes Modell einer B-17 Flying Fortress im Maßstab. weshalb ich es gekauft habe, da es meine Absicht war, es realistischer zu bemalen und es ein wenig zu modifizieren, um es etwas realistischer zu machen. Es fliegt sehr gut und sieht toll aus in der Luft. Hier ist ein Bild von mir, nachdem ich es mit etwas silberner Farbe und einigen zusätzlichen Markierungen etwas aufgepeppt habe.
good plane but a bit expensive and has two motors and not 4 so don’t be fooled by the pictures. not like me anyway lol . recommend perfect for beginners.
Very simple, two channel differential thrust plane that required almost no assembly. All you do is glue on the fin, and a tube of glue is supplied for that purpose. There are also 3 wheels that plug into slots on the wings and fuselage, but you can fly without those, and they are easy to remove and refit. The inner two engines have motors fitted, but the outer ones are just dummies, but they have propellers that spin with the slipstream. The motors are 8x20 brushless which give more than enough power. The props rotate in opposite directions, and a spare of each type is supplied, as well as a 450mAh flight battery and a charger for the battery that plugs into a USB port. There are couple of problems you should fix or you will be disappointed. 1. The propellers are not a tight enough fit on the motor shafts, so as soon as you throttle up they will fly off. You can fix this y putting a piece of thread through the shaft hole on the propeller, which goes right through to the front. Then push the prop back on so the thread is trapped. It also doesn't hurt to wick a tiny amount of CA glue (superglue) through the front of the prop so it gets onto the shaft and the thread. Cut off any thread that sticks out using a modelling knife or razor blade. 2. The model won't climb, no matter how much throttle you apply, unless you do some work on the elevators to give it just a tiny bit of up elevator. About 2mm up at the trailing edge of each elevator is enough. First you need to cut away two tiny pieces of foam that join the elevators to the rest of the horizontal stabilizer and to the fuselage, so that the elevators become free to move. I used two tiny pieces of toothpick stuck into the fuselage to lift the elevators just enough, then a very small piece of sticky tape to hold them in position and stop them from moving in flight (see photo). With these changes, the plane will fly quite well. The gyro makes it very stable.
Tolles Modellflugzeug! Es fliegt gut mit 4 g zusätzlichem Nasengewicht. Ich habe wieder eines gekauft. Ich habe mit sehr scharfen Modellfarben gemalt, um realistischer auszusehen. Daneben steht eine alte Matchbox B-17 G im Maßstab 1:72.
tolles Produkt und rechtzeitige Lieferung
Tolles Modellflugzeug! Es fliegt gut mit 4 g zusätzlichem Nasengewicht. Ich habe wieder eines gekauft. Ich habe mit sehr scharfen Modellfarben gemalt, um realistischer auszusehen. Daneben steht eine alte Matchbox B-17 G im Maßstab 1:72. Ich habe die modifizierten Fahrwerke hinzugefügt.
Tolles Modellflugzeug! Es fliegt gut mit 4 g addeg Nasengewicht.
Lim Ting sagt Fliegen Schwanz schwer! sicherzustellen, dass Propeller sind eng vor der Beobachtung Propeller fliegen entfernt befestigt. kann Außenborder Propeller für bessere ruhige Flug Außenborder Requisiten Arbeit an Bord Motoren. auch gibt es Cutaways, um ein Servo für Aufzug Kontrolle hinzuzufügen. jedoch aktuelle Elektronik nicht unterstützen.
sehr schönes kleines Flugzeug
sieht gut aus und sind relativ schnell gekommen