Kundenbewertungen

Eine Bewertung schreiben
  • Alle Bewertungen (758)
  • Bild (97)
  • Video (23)
  • Alle Sterne
    • Alle Sterne(758)
    • 5 Sterne(697)
    • 4 Sterne(40)
    • 3 Sterne(12)
    • 2 Sterne(6)
    • 1 Sterne(3)
Sortiere durch:
Zur Vorschau
  • Zur Vorschau
  • Am hilfreichsten
  • Die letzten
Bewertungen nur aus Ihrem Land (Germany)
|
Original zeigen

Ein Teil der Rezension wurde automatisch übersetzt.

  • 11/05/2017

    FC looks very good. Packed in a box and antistatic paket. USB cable, power cable with connector and mounting screws with adsorbers are included in package. PCB and soldering quality is great. Succesfuly paired with FlySky FS-I6X in AFHDS 2A Mode. Succesfuly connected to Betaflight. Stock version of BF is 3.1.0 Target SPRASINGF3EVO. Succesfuly updated to BF v.3.1.7. There is a little assimetry of transmiiter channels and little jitter in midpoints. It can be corrected with transmitter calibration.

    Kommentar (2)
    Original zeigen
  • 22/05/2017

    This flight controller is prefect if you are looking to step your tiny whoop game up to the next level. It allows you to take an E010 or E010S frame (or probably blade inductrix frame also) and 6mm motors and go fly some acro! The board has plug ins for the motors so no excessive soldering, just the power and the camera. I got the Flysky version of the board because I have a Turnigy Evolution and it was incredibly easy to bind. I plugged in the board to the computer and betaflight was already installed, nice! (note here is the only con I can think of for the board, the position of the micro usb plug required that I remove a prop to plug into the computer, this is why the 4 stars for appearance) Anyway, I built mine with some fancy gold 73,000 RPM motors with the 3 blade props but I think the purple racestar 67000 RPM ones from banggood would be plenty. I also suggest using a JST PH2.0 connector rather than the one they provide because I think the best batteries are the Nitro Nectar HV 4.35V 250mah 30/60c that they now have a copy of on here that I am going to try out as well. Set up and build was pretty easy even though this was my first time trying it. I did cut down the rubber standoffs to make the mounting easier, other than that it was simple. And it flies great! I need to practice my acro skills though, haha oh FYI my finished build is 21g with no battery For the price this has got the be the best value around! Oh an dont forget to disarm asap after a crash!

    Kommentar
    Original zeigen
  • 17/11/2016

    From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight

    Kommentar (2)
    Original zeigen
  • 11/05/2021

    Sehr zufrieden und nah an Perfect! Zu Beginn empfehle ich, das PPM-Protokoll zu vermeiden. Die Betaflight-Version ist entscheidend und ihre Konfiguration vielleicht "knifflig". Das Board kann sich seltsam verhalten: 1 - Das RANGE 1000-2000 ist nicht erhältlich. 2 - Die RANGE (außer 1000-2000) schwankt. An einem Tag kann sie Werte anzeigen, am nächsten Tag andere Werte. 3 - Beim Anpassen des RANGE mit dem Befehl RXRANGE wird das Verhalten der Drohne zu " unvorhersehbar": a) Die Drossel darf plötzlich ", hebt ab ". Die Drohne springt dann in jede Richtung. b) Board ist übermäßig ausfallsicher oder reboot. Es scheint wie Board, Batterie oder beide Dysfunktion. c) Möglicherweise verliert die Drohne plötzlich an Höhe. Abgesehen von der Fluktuation und der fehlenden Reichweite durch den PPM / DSM2 - Empfänger sind die genannten Störungen aufgrund (in meinem Fall) der Konfiguration. So lösen Sie: - Die Karte / Die Drohne muss vor dem Setzen einer Kamera richtig funktionieren (Im Falle von PB, testen/konfigurieren Sie mit einer Version von BTFL < = 3.5.6). - Vermeiden Sie RXRANGE . Mein aktueller Bereich ist 1060-1860. Er kann bis 1053-1853 runtergehen. (Die unterschiedlichen Schwellenwerte und Deadbands werden entsprechend angepasst). Nach der Zugabe von Verbinder, Gummi und Heißkleber hat sich das Design weiterentwickelt, um das Gewicht bei 20g zu halten. Durch den PPM-Empfänger ist die Drohne wahrscheinlich etwas weniger leistungsfähig als die SBUS-Version, aber sie funktioniert sehr gut und mit Eachine E010 1s 3.7V 200mAh 30C Batterien (0 Höhenverlust und volle Geschwindigkeit). Also: (Zum Abschluss) Produkt ist AE (Wie erwartet). Packungsinhalt ist großartig, aber mit 2 oder 3 Schrauben wäre es noch besser (Nah an perfekt). Thx

    Kommentar
    Original zeigen
  • 26/02/2017

    Thisi is the second one I got and this one works like a charm. Got some recerstar 615 motors simple frame using my old flysky put everything together in about 15 minutes bound and hooked to cleanflight and bammmmm i'm flying worked quick and easy and flies great. Might flash betaflight but for now it works great for around the office and around the house.

    Kommentar (2)
    Original zeigen
  • 01/09/2017

    I bought the Eachine E010s fly sky version and was upset when it wouldn't link with my FS-I6S radio because it was strictly AFHDS 2A but with this inexpensive board it works! Remember to solder the power leads and the camera leads together blacks on ground reds on VCC.

    Kommentar (1)
    Original zeigen
  • 28/09/2017

    Works very good now. The instruction manual is out of date and only marginally helpful. Has a bind button. The installed spracing_f3_evo firmware was full of bugs. Flashed the latest (3.1.7) and it's fixed.Unfortunately, the configuration will be empty/defaults which means starting from scratch (or copy a saved config.). Flies okay with the default Betaflight PIDs. I may spend some time fine tuning afterwards. Board doesn't have a BEC for the camera. Camera shares the current directly from the battery connection. The placement of the USB connector is awkward and that is the only complaint I have. This board is lavishly endowed with LEDs. Easy to see the direction flying line of site. The FCB (and FPV camera) are soft mounted with the included rubbers and screws. I'm using LiPo batteries with micro connectors so the included connector went unused. 66000 rpm (no load) motors. 220mAh 45C LiPo battery. 6 minute flights. It weighs 20.1g

    Kommentar (2)
    Original zeigen
  • 25/06/2017

    Frsky version delivered with Cleanflight Firmware, USB cable and some mounting material. Sucessfully flashed latest Betaflight. The position of the USB connector on the board is not the best option. You always have to dismouted the prop if changes are needed. Additionally there seems the be a little jitter between 10 and 20 us on the channel which has to be corrected in the Tx.

    Kommentar
    Original zeigen
  • 21/08/2017

    Received this board months ago but left it to sit on a shelf. feature set is exactly what I wanted. I have not been able to use it. board powers and binds giving a solid green light but has no function in betaflight. my board is the 2A version and has a bind button. the PDF instructions for Flysky do not match my item. https://youtu.be/mY9808_KBDg

    Kommentar (4)
    Original zeigen
  • 19/10/2017

    Wszystko ok i działa jak należy Tiny na ramie e010 lata idealnie stabilny żadnych niepożądanych drgań. miałem chwilowy kłopot z ustawieniami cos namieszałem i fc nie widział aparatury mimo że zbindowana była ale po resecie wróciło wszystko do normy. polecam.

    Kommentar
    Original zeigen
Show:

    Gesamt 0 Seiten

    Zur Seite gehen

    Sie interessieren sich vielleicht für:

    recommendation for you
    • US$9.23
    • US$19.35
    • US$16.99
    • US$26.99
    • US$102.99
    • US$59.99
    • US$17.31
    • US$38.99
    • US$23.59
    • US$24.99
    • US$75.99
    • US$15.99
    • US$11.99
    • US$51.99
    • US$29.99
    • US$13.64
    • US$13.64
    • US$63.99