Kam vor der Deadline und kam alles, was ich bat, jetzt werde ich testen

veio antes do prazo e chegou tudo o que eu pedi agora vou testar

Kam vor der Deadline und kam alles, was ich bat, jetzt werde ich testen

OK

ok

OK

The module that was shipped out to me, although physically similar in layout, used a similar 8 pin (but umarked and with a different pin out) to the MP1584 shown in the product photos. The trimpot was faulty, causing great difficulty in setting the output to 5.15 volts and prone to generating excessive voltage at random points of the adjustment range. I replaced the trimpot with a 33KR smd resistor and added a 200KR across the 6K2R smd resistor between ground and the Vref pin to trim it to 5.2v. Having modified it to give a reliable 5.2v output, I then discovered that it had excessive ripple, 400mVp-p no load rising to 800mV or more with a 1A test load. I gave up on this module and tried another one which had option solder bridge jumper links for 3.3, 5, 9 and 12 volt outputs along with an adj option where I discovered the pot had been replaced with a 39KR to preset it to 5 volts, saving the need to bridge any of the voltage option jumpers. This had much less voltage ripple but unfortunately I managed to burn out its very tiny IC when probing with a DMM to track down why it had suddenly taken a dislike to my add on LC filter. It had worked ok until then but now it was back to this variable voltage converter module where I discovered that the shottky diode had been left disconnected from the inductor via an open solder bridge jumper which I bridged with a blob of solder and saw a 6dB reduction in output ripple voltage. Still not marvellous but with the additional LC filtering, it was down to a p-p of 24 to 90mV (rms of 2.5 to 4mV). I'm fully aware of all the pitfalls in using a 'scope to examine ripple voltage waveforms hence my use of a 12v SLA to power it to minimise ground loop interference from other smpsu sources (including the 'scope's own psu). To say I was unimpressed by the example I'd received would be an understatement! I suspect the one actually pictured will be a lot better (just make sure the pot isn't a "timebomb in waiting" before using it).

The module that was shipped out to me, although physically similar in layout, used a similar 8 pin (but umarked and with a different pin out) to the MP1584 shown in the product photos. The trimpot was faulty, causing great difficulty in setting the output to 5.15 volts and prone to generating excessive voltage at random points of the adjustment range. I replaced the trimpot with a 33KR smd resistor and added a 200KR across the 6K2R smd resistor between ground and the Vref pin to trim it to 5.2v. Having modified it to give a reliable 5.2v output, I then discovered that it had excessive ripple, 400mVp-p no load rising to 800mV or more with a 1A test load. I gave up on this module and tried another one which had option solder bridge jumper links for 3.3, 5, 9 and 12 volt outputs along with an adj option where I discovered the pot had been replaced with a 39KR to preset it to 5 volts, saving the need to bridge any of the voltage option jumpers. This had much less voltage ripple but unfortunately I managed to burn out its very tiny IC when probing with a DMM to track down why it had suddenly taken a dislike to my add on LC filter. It had worked ok until then but now it was back to this variable voltage converter module where I discovered that the shottky diode had been left disconnected from the inductor via an open solder bridge jumper which I bridged with a blob of solder and saw a 6dB reduction in output ripple voltage. Still not marvellous but with the additional LC filtering, it was down to a p-p of 24 to 90mV (rms of 2.5 to 4mV). I'm fully aware of all the pitfalls in using a 'scope to examine ripple voltage waveforms hence my use of a 12v SLA to power it to minimise ground loop interference from other smpsu sources (including the 'scope's own psu). To say I was unimpressed by the example I'd received would be an understatement! I suspect the one actually pictured will be a lot better (just make sure the pot isn't a "timebomb in waiting" before using it).

The module that was shipped out to me, although physically similar in layout, used a similar 8 pin (but umarked and with a different pin out) to the MP1584 shown in the product photos. The trimpot was faulty, causing great difficulty in setting the output to 5.15 volts and prone to generating excessive voltage at random points of the adjustment range. I replaced the trimpot with a 33KR smd resistor and added a 200KR across the 6K2R smd resistor between ground and the Vref pin to trim it to 5.2v. Having modified it to give a reliable 5.2v output, I then discovered that it had excessive ripple, 400mVp-p no load rising to 800mV or more with a 1A test load. I gave up on this module and tried another one which had option solder bridge jumper links for 3.3, 5, 9 and 12 volt outputs along with an adj option where I discovered the pot had been replaced with a 39KR to preset it to 5 volts, saving the need to bridge any of the voltage option jumpers. This had much less voltage ripple but unfortunately I managed to burn out its very tiny IC when probing with a DMM to track down why it had suddenly taken a dislike to my add on LC filter. It had worked ok until then but now it was back to this variable voltage converter module where I discovered that the shottky diode had been left disconnected from the inductor via an open solder bridge jumper which I bridged with a blob of solder and saw a 6dB reduction in output ripple voltage. Still not marvellous but with the additional LC filtering, it was down to a p-p of 24 to 90mV (rms of 2.5 to 4mV). I'm fully aware of all the pitfalls in using a 'scope to examine ripple voltage waveforms hence my use of a 12v SLA to power it to minimise ground loop interference from other smpsu sources (including the 'scope's own psu). To say I was unimpressed by the example I'd received would be an understatement! I suspect the one actually pictured will be a lot better (just make sure the pot isn't a "timebomb in waiting" before using it).

Отличный модуль брал для 5 вольтовой камеры, чтобы не тащить на столб 220В. Провел 12В, и используя этот преобразователь получил 5В. Понравилась маленькими размерами и экономичностью.

Отличный модуль брал для 5 вольтовой камеры, чтобы не тащить на столб 220В. Провел 12В, и используя этот преобразователь получил 5В. Понравилась маленькими размерами и экономичностью.

Отличный модуль брал для 5 вольтовой камеры, чтобы не тащить на столб 220В. Провел 12В, и используя этот преобразователь получил 5В. Понравилась маленькими размерами и экономичностью.

Nun, ein schönes und gutes Modul, aber wirklich klein! Ich riskierte, es in den Müll mit dem Umschlag zu werfen. Weitere technische Details, wenn ich es im Dienst

Well, a nice and good module, but really small ! I risked to throw it in the garbage with the envelope. More technical details when I put it on duty

Nun, ein schönes und gutes Modul, aber wirklich klein! Ich riskierte, es in den Müll mit dem Umschlag zu werfen. Weitere technische Details, wenn ich es im Dienst

Gute Qualität.

Good quality.

Gute Qualität.

works well

works well

works well

große Step-Down-Konverter, nur bedenken Sie, dass Sie sie zuerst mit dem kleinen philips Kopf Potentiometer konfigurieren, da es viel mehr als nur 5v herausgeben kann, Sie können es für 12v Ausgabe usw. verwenden, Seien Sie sich bewusst und verwenden Sie ein Multimeter, um es auf 5v Ausgang

great step-down converters, just keep in mind you should first configure them with the small philips head potentiometer as it can put out much more than just 5v, you can use it for 12v output etc, just be aware and use a multimeter to put it to 5v output

große Step-Down-Konverter, nur bedenken Sie, dass Sie sie zuerst mit dem kleinen philips Kopf Potentiometer konfigurieren, da es viel mehr als nur 5v herausgeben kann, Sie können es für 12v Ausgabe usw. verwenden, Seien Sie sich bewusst und verwenden Sie ein Multimeter, um es auf 5v Ausgang

Sajnálattos módon a termék sérült volt. De működik.

Sajnálattos módon a termék sérült volt. De működik.

Sajnálattos módon a termék sérült volt. De működik.

Brauchte es um einen Akku im Radio mit 12 V vom Wohnwagen zu laden. Geht perfekt.

Brauchte es um einen Akku im Radio mit 12 V vom Wohnwagen zu laden. Geht perfekt.

Brauchte es um einen Akku im Radio mit 12 V vom Wohnwagen zu laden. Geht perfekt.