First things first. If you are the kind of person that wants to click one button and everything works perfectly this is not for you. for everybody else its a decent printer. Build time 4 hours, everything you need is provided. Tweaking and getting it to run good took me another 2-4 hours. Things that are great: - Stable frame - Heated bed that provides really good bed adhesion (almost too good) - Complete kit Things that could be better: - The support frame for the y axis is very thin. If you are fighting to remove a print from the bed you can and will bend it slightly. And this means you will have to adjust the bed level again. - My bed wasn't perfectly flat, this can be problematic for larger prints. but is easily solved by using a glass plate or a raft during printing. - the hot end fan is controlled by the cooling fan pwm. This is not OK and I had to change this. If you were to run a print without the cooling fan enabled your hotend will overheat and clog up. I opened the control box and rewired the fan to the 12V rail to be always on. Do change this!! - micro SD slot.... awfull. I had several occations where i tried to push in the sd card and missed the actual port. then you have to open up the control box to get your micro sd card back. Do yourself a favour and get a micro to sd adapter http://tiny.cc/023huy Things to watch out for - spend a little time adjusting all the eccentric bearing bushings. too much pressure causes them to wear quickly - print yourself a filament guide to prevent the filament from touching the Z axis. - don't try to print too fast, the extruder will be your limiting factor here, you could consider upgrading this. All in all, not too bad, not too bad at all Cheers!

First things first. If you are the kind of person that wants to click one button and everything works perfectly this is not for you. for everybody else its a decent printer. Build time 4 hours, everything you need is provided. Tweaking and getting it to run good took me another 2-4 hours. Things that are great: - Stable frame - Heated bed that provides really good bed adhesion (almost too good) - Complete kit Things that could be better: - The support frame for the y axis is very thin. If you are fighting to remove a print from the bed you can and will bend it slightly. And this means you will have to adjust the bed level again. - My bed wasn't perfectly flat, this can be problematic for larger prints. but is easily solved by using a glass plate or a raft during printing. - the hot end fan is controlled by the cooling fan pwm. This is not OK and I had to change this. If you were to run a print without the cooling fan enabled your hotend will overheat and clog up. I opened the control box and rewired the fan to the 12V rail to be always on. Do change this!! - micro SD slot.... awfull. I had several occations where i tried to push in the sd card and missed the actual port. then you have to open up the control box to get your micro sd card back. Do yourself a favour and get a micro to sd adapter http://tiny.cc/023huy Things to watch out for - spend a little time adjusting all the eccentric bearing bushings. too much pressure causes them to wear quickly - print yourself a filament guide to prevent the filament from touching the Z axis. - don't try to print too fast, the extruder will be your limiting factor here, you could consider upgrading this. All in all, not too bad, not too bad at all Cheers!

First things first. If you are the kind of person that wants to click one button and everything works perfectly this is not for you. for everybody else its a decent printer. Build time 4 hours, everything you need is provided. Tweaking and getting it to run good took me another 2-4 hours. Things that are great: - Stable frame - Heated bed that provides really good bed adhesion (almost too good) - Complete kit Things that could be better: - The support frame for the y axis is very thin. If you are fighting to remove a print from the bed you can and will bend it slightly. And this means you will have to adjust the bed level again. - My bed wasn't perfectly flat, this can be problematic for larger prints. but is easily solved by using a glass plate or a raft during printing. - the hot end fan is controlled by the cooling fan pwm. This is not OK and I had to change this. If you were to run a print without the cooling fan enabled your hotend will overheat and clog up. I opened the control box and rewired the fan to the 12V rail to be always on. Do change this!! - micro SD slot.... awfull. I had several occations where i tried to push in the sd card and missed the actual port. then you have to open up the control box to get your micro sd card back. Do yourself a favour and get a micro to sd adapter http://tiny.cc/023huy Things to watch out for - spend a little time adjusting all the eccentric bearing bushings. too much pressure causes them to wear quickly - print yourself a filament guide to prevent the filament from touching the Z axis. - don't try to print too fast, the extruder will be your limiting factor here, you could consider upgrading this. All in all, not too bad, not too bad at all Cheers!

(britischer Kunde) Dies ist mein erster Drucker (ich habe bereits Erfahrung mit Industriedruckern, aber nicht mit Consumer-Maschinen) Ich kann nicht hoch genug von diesem Drucker sprechen. kam innerhalb von 48 Stunden und sehr gut verpackt (es gab Beulen auf der Schachtel, aber nichts Haupt). Hat mich etwa 45-50 Minuten zu montieren und zu überprüfen (empfehlen Online-Videos für den Bau, wie die Anweisungen bekommen die Arbeit zu tun, aber sind sehr chaotisch und nicht sehr klar). Es wurde das mitgelieferte Filament verwendet, das mehr als genug für den Testdruckhund war, den ich wählte (100% Fill) und es kam wirklich gut, keine Probleme, Da war ein bisschen Überbrückung mit dem Schwanz und den Ohren aber gleich aus der Kiste zu erwarten. Einrichtungshinweis: - stellen Sie sicher, dass Sie einen guten Platz zum Arbeiten haben (behandeln Sie es wie den Bau eines PCs ) - Nivellieren Sie das Bett 3-4 Mal, bevor Sie mit dem Drucken beginnen - Prüfen Sie alle Schrauben und Muttern, geben Sie dem Drucker ein leichtes Wackeln, um zu sehen, ob Sie irgendwelche losen Teile hören können - Prüfen Sie die Gurte, ob sie klar und gespannt für einen reibungslosen Lauf sind. - Nutzen Sie Videos online als Referenz und schauen Sie sich vor dem Start durch das Display und die Einstellungen, damit Sie mit allen Einstellungen und Menüs vertraut sind.

(UK customer) This is my first printer (I have had previous experience with industry grade printers but not consumer machines) I cannot speak highly enough of this printer. came within 48 hours and very well packaged (there were dents on the box but nothing major). Took me about 45-50 mins to assemble and check (recommend online videos for construction as the instructions get the job done but are very chaotic and no very clear). Used the filament included which was more than enough for the test print dog I chose (100% Fill) and It came out really well, no issues, there was a bit of bridging with the tail and ears but to be expected straight out of the box. Setup advice: - make sure you have a good space to work on (treat it like building a PC ) - level the bed 3-4 times before you start printing - check all nuts and bolts, give the printer a slight wobble to see if you can hear any loose parts - check the belts make sure they are clear and tensioned for a smooth run. - use videos online for reference and have a look through the display and settings before starting so you are familiar with all the settings and menus.

(britischer Kunde) Dies ist mein erster Drucker (ich habe bereits Erfahrung mit Industriedruckern, aber nicht mit Consumer-Maschinen) Ich kann nicht hoch genug von diesem Drucker sprechen. kam innerhalb von 48 Stunden und sehr gut verpackt (es gab Beulen auf der Schachtel, aber nichts Haupt). Hat mich etwa 45-50 Minuten zu montieren und zu überprüfen (empfehlen Online-Videos für den Bau, wie die Anweisungen bekommen die Arbeit zu tun, aber sind sehr chaotisch und nicht sehr klar). Es wurde das mitgelieferte Filament verwendet, das mehr als genug für den Testdruckhund war, den ich wählte (100% Fill) und es kam wirklich gut, keine Probleme, Da war ein bisschen Überbrückung mit dem Schwanz und den Ohren aber gleich aus der Kiste zu erwarten. Einrichtungshinweis: - stellen Sie sicher, dass Sie einen guten Platz zum Arbeiten haben (behandeln Sie es wie den Bau eines PCs ) - Nivellieren Sie das Bett 3-4 Mal, bevor Sie mit dem Drucken beginnen - Prüfen Sie alle Schrauben und Muttern, geben Sie dem Drucker ein leichtes Wackeln, um zu sehen, ob Sie irgendwelche losen Teile hören können - Prüfen Sie die Gurte, ob sie klar und gespannt für einen reibungslosen Lauf sind. - Nutzen Sie Videos online als Referenz und schauen Sie sich vor dem Start durch das Display und die Einstellungen, damit Sie mit allen Einstellungen und Menüs vertraut sind.

Hai this is my first 3d pritner, in mine printer i got injecton moulded power supply cover, where has shashi got 3d printed one. The printer is assembled and working the first print quality also nice. Thanks for every one

Hai this is my first 3d pritner, in mine printer i got injecton moulded power supply cover, where has shashi got 3d printed one. The printer is assembled and working the first print quality also nice. Thanks for every one

Hai this is my first 3d pritner, in mine printer i got injecton moulded power supply cover, where has shashi got 3d printed one. The printer is assembled and working the first print quality also nice. Thanks for every one

05076700387 ürün hakkında sorusu olan arayabilir yardımcı olurum

05076700387 ürün hakkında sorusu olan arayabilir yardımcı olurum

05076700387 ürün hakkında sorusu olan arayabilir yardımcı olurum

The printer is good strong in structure. the assemble is simple and all assembly instruction given in manual as well as memory card which helps to assemble withe ease. The printer assembly which is DIY i am loving it. The printer prints also well. i have to adjust the print settings. The printer has some minor issues we faced during installation like x carriage and z carriage or not moving through the aluminium T slot because of slight variation in the measurements. that is solved just simply by loosing the nuts of bearing.

The printer is good strong in structure. the assemble is simple and all assembly instruction given in manual as well as memory card which helps to assemble withe ease. The printer assembly which is DIY i am loving it. The printer prints also well. i have to adjust the print settings. The printer has some minor issues we faced during installation like x carriage and z carriage or not moving through the aluminium T slot because of slight variation in the measurements. that is solved just simply by loosing the nuts of bearing.

The printer is good strong in structure. the assemble is simple and all assembly instruction given in manual as well as memory card which helps to assemble withe ease. The printer assembly which is DIY i am loving it. The printer prints also well. i have to adjust the print settings. The printer has some minor issues we faced during installation like x carriage and z carriage or not moving through the aluminium T slot because of slight variation in the measurements. that is solved just simply by loosing the nuts of bearing.

Hervorragende Wahl für die Person mit einem lo Budget. Natürlich gibt es bessere Modelle, aber Preis / Effizienz Ich denke, es ist schwer zu überbieten. Sie können eine Menge Tweaking in der Einrichtung als gut. Ein negativer Aspekt sind die Nivellierschrauben. Es ist ziemlich schwer, sie alle zusammen zu bekommen. Auch ich mag, dass ich alles zusammen aus der Box zusammenbauen muss, ein bisschen lehrreich im Vergleich zu einer RTP-Maschine. Ich würde auf jeden Fall wieder einen kaufen, wenn dieser irgendwie gestohlen oder angezündet wird. 🤣

Excellent choice for the person with a lo budget. Of course there is better models, but price/efficiency I think it's hard to beat. You can make a lot of tweaking in the setup as well. One negative aspect is the leveling screws. It's pretty hard to getting them all to work together. Also I like that I have to assemble it all together from the box, a bit educational compared to a RTP machine. I would definitely buy one again if somehow this one gets stolen or set on fire. 🤣

Hervorragende Wahl für die Person mit einem lo Budget. Natürlich gibt es bessere Modelle, aber Preis / Effizienz Ich denke, es ist schwer zu überbieten. Sie können eine Menge Tweaking in der Einrichtung als gut. Ein negativer Aspekt sind die Nivellierschrauben. Es ist ziemlich schwer, sie alle zusammen zu bekommen. Auch ich mag, dass ich alles zusammen aus der Box zusammenbauen muss, ein bisschen lehrreich im Vergleich zu einer RTP-Maschine. Ich würde auf jeden Fall wieder einen kaufen, wenn dieser irgendwie gestohlen oder angezündet wird. 🤣

after using anet a8 for 7 months I got this ender 3 it's so good printer also amazing price

after using anet a8 for 7 months I got this ender 3 it's so good printer also amazing price

after using anet a8 for 7 months I got this ender 3 it's so good printer also amazing price

Excelente produto. Fui tarifado em R$511,00.

Excelente produto. Fui tarifado em R$511,00.

Excelente produto. Fui tarifado em R$511,00.

Chegou tudo corretamente e funcionando perfeitamente. Recomendo.

Chegou tudo corretamente e funcionando perfeitamente. Recomendo.

Chegou tudo corretamente e funcionando perfeitamente. Recomendo.

Très bonne imprimante, aucun problème avec elle est top pour sont prix. Seule demol c'est de la réglé le calibrage pour l'impression c'est casse couille à faire et il faut être très patient. J'ai mis plus 1 semaine pour l'avoir en main et comprendre heureusement que y'a YouTube lol 😂 . Programme en Anglais mais facile à comprendre.

Très bonne imprimante, aucun problème avec elle est top pour sont prix. Seule demol c'est de la réglé le calibrage pour l'impression c'est casse couille à faire et il faut être très patient. J'ai mis plus 1 semaine pour l'avoir en main et comprendre heureusement que y'a YouTube lol 😂 . Programme en Anglais mais facile à comprendre.

Très bonne imprimante, aucun problème avec elle est top pour sont prix. Seule demol c'est de la réglé le calibrage pour l'impression c'est casse couille à faire et il faut être très patient. J'ai mis plus 1 semaine pour l'avoir en main et comprendre heureusement que y'a YouTube lol 😂 . Programme en Anglais mais facile à comprendre.