Kundenbewertungen

4.88 aus 5
Eine Bewertung schreiben
  • Alle Bewertungen (226)
  • Image (25)
  • Video (0)
  • All Star
    • All Star(226)
    • 5 Star(209)
    • 4 Star(12)
    • 3 Star(3)
    • 2 Star(0)
    • 1 Star(2)
Sortiere durch:
Zur Vorschau
  • Zur Vorschau
  • Am hilfreichsten
  • Die letzten
Bewertungen nur aus Ihrem Land (Germany)
  • February-22 2020 11:10:40

    Good product. Reads temperature, humidity, pressure and altitude. Tested the values with internet, and the values are a bit off, but all in all accurate enough. Note that this is a BME280 clone with SPI bus and won't work with I2C. Used some extra days on shipping, but I'm still overall pleased with my purchase.

    Kommentar
  • April-18 2020 08:19:37

    Globalement bon produit, bonne fabrication, mais qualité moyenne, emballage antistatique

    Kommentar
  • October-06 2020 10:42:09

    Good quality. Works well

    Kommentar
  • October-01 2020 12:59:23

    Good price an quality.

    Kommentar
  • January-31 2020 05:21:29

    Always a fantastic product

    Kommentar
  • September-09 2020 10:51:52

    Fast delivery, proper packaging, testing in progress. Thanks

    Kommentar
  • May-05 2019 03:18:24

    the model received is not exactly of the image, but it's a true BME280 and works perfectly. the breadboard contains a pull-up resistors, necessary for I2C and SPI protocols. I have worked directly on arduino, but for security, you use a level-shifter for adapt the logic levels (5v-to-3.3v). pd. I see multiple comments that say that module is not a BME280, is a BMP280. The marks on the module can induce an error, but the chip is a REAL BME280 and reads good the temperature, pressure and humidity

    Kommentar (1)
  • February-23 2018 14:56:34

    I just hooked this up to an ESP8266 NodeMCU board using the Arduino IDE and firmware and it works great with the Adafruit BME280 library. Like others have said, I just had to change the I2C address to 0x76. The temp and humidity values seem comparable to the readings I was getting from the DHT22 sensor that I replaced with this because I also wanted barometric pressure readings. Wish these would be a bit cheaper but I only need one of them, the rest of my boards will be fine with DHT22s for temperature

    Kommentar
  • October-17 2019 08:38:34

    this is NOT the BME280, I got BMP280 with no humidity reported by the sensor. The marking on the chip shows it, too, as I know for now. I trusted the reviews, but obviously they changed the board. You can look it up in the data sheets: BME280: https://www.embeddedadventures.com/datasheets/BME280.pdf (chapter 7.7) BMP280: https://cdn-shop.adafruit.com/datasheets/BST-BMP280-DS001-11.pdf (chapter 7.3) The BME280 with humidity measurement has one dot and one vent hole, the BMP280 only has one dot -

    Kommentar
  • December-30 2016 04:02:53

    Can work I2C or SPI. In the picture work SPI. Nice accuracy and resolution data :) Recommend. Descriptions of parameters shown in the attached image in Polish ;)

    Kommentar
Show:

    Total 0 pages

    Go to page

    Go

    Sie interessieren sich vielleicht für:

    recommendation for you
    • 3,29€
    • 9,07€
    • 8,24€
    • 5,77€
    • 4,12€
    • 7,42€
    • 4,33€
    • 4,94€
    • 3,29€
    • 11,54€
    • 1,39€
    • 12,36€
    • 1,64€
    • 1,28€
    • 3,20€
    • 1,64€
    • 1,64€
    • 3,72€