Buy 2 samples until arrived after connected output antenna and supply it at 12Vdc draw more then 0,3Amp and start burned !!!!! on IC2. Second sample tested again at 12 Vdc , Not burned but hot too and power RF amplierf doesn't more than 10dB. For me very poor device maybe weren't 2 lucky pieces....

Buy 2 samples until arrived after connected output antenna and supply it at 12Vdc draw more then 0,3Amp and start burned !!!!! on IC2. Second sample tested again at 12 Vdc , Not burned but hot too and power RF amplierf doesn't more than 10dB. For me very poor device maybe weren't 2 lucky pieces....

Buy 2 samples until arrived after connected output antenna and supply it at 12Vdc draw more then 0,3Amp and start burned !!!!! on IC2. Second sample tested again at 12 Vdc , Not burned but hot too and power RF amplierf doesn't more than 10dB. For me very poor device maybe weren't 2 lucky pieces....

Goods received in perfect condition through postal services in about 4-5 weeks time, which is absolutely normal. The goods were checked in the RF workshop, and turned out to be capable of 1 Watt Maximum output by feeding 0dBm (1 milliwatt input), confirming the reliable almost uniform gain within the specified band (1-700MHz) of 30dB with linearity. We could not test it at higher power levels due to limitation of our Rf signal generator, whose output power level is limited to 0dBm (1 mW) max. Further investigation revealed that the module uses the following components with suggested power levels recommended by the manufacturer for reliable operation. RD01MUS1 (SMD CODE - K2) as the final stage rated for 520MHz, 1Watt SBA-5089Z-Sirenza. (SMD CODE - BA5Z) as the first driver stage. It may be possible to use this module at higher power levels, However we ourselves use the devices safely to half of their capacity for long term reliability for continuous operation. I am very happy to use them between 0.5 ~ 1.0 watts for our applications.... Very satisfied with the results, this will find use in various applications.

Goods received in perfect condition through postal services in about 4-5 weeks time, which is absolutely normal. The goods were checked in the RF workshop, and turned out to be capable of 1 Watt Maximum output by feeding 0dBm (1 milliwatt input), confirming the reliable almost uniform gain within the specified band (1-700MHz) of 30dB with linearity. We could not test it at higher power levels due to limitation of our Rf signal generator, whose output power level is limited to 0dBm (1 mW) max. Further investigation revealed that the module uses the following components with suggested power levels recommended by the manufacturer for reliable operation. RD01MUS1 (SMD CODE - K2) as the final stage rated for 520MHz, 1Watt SBA-5089Z-Sirenza. (SMD CODE - BA5Z) as the first driver stage. It may be possible to use this module at higher power levels, However we ourselves use the devices safely to half of their capacity for long term reliability for continuous operation. I am very happy to use them between 0.5 ~ 1.0 watts for our applications.... Very satisfied with the results, this will find use in various applications.

Goods received in perfect condition through postal services in about 4-5 weeks time, which is absolutely normal. The goods were checked in the RF workshop, and turned out to be capable of 1 Watt Maximum output by feeding 0dBm (1 milliwatt input), confirming the reliable almost uniform gain within the specified band (1-700MHz) of 30dB with linearity. We could not test it at higher power levels due to limitation of our Rf signal generator, whose output power level is limited to 0dBm (1 mW) max. Further investigation revealed that the module uses the following components with suggested power levels recommended by the manufacturer for reliable operation. RD01MUS1 (SMD CODE - K2) as the final stage rated for 520MHz, 1Watt SBA-5089Z-Sirenza. (SMD CODE - BA5Z) as the first driver stage. It may be possible to use this module at higher power levels, However we ourselves use the devices safely to half of their capacity for long term reliability for continuous operation. I am very happy to use them between 0.5 ~ 1.0 watts for our applications.... Very satisfied with the results, this will find use in various applications.

Verwenden Sie vor dem Anschluss Silikonfett unter den Transistoren. Die maximale Spannung beträgt 12 V. Die Transistoren arbeiten in der Klasse A. Bei 12 V beträgt der Strom 0,45 A. 1,25 W Ausgangsleistung, 27 dB Leistungsverstärkung bei f = 400 MHz. Er eignet sich als symmetrischer Endstufe-Treiber der Klasse B. Die Lieferzeit betrug 60 Tage.

Before connecting, use silicone grease under the transistors. The maximum voltage is 12 V. The transistors operate in class A. At 12 V, the current is 0.45 A. 1.25 W output power, 27 dB power gain at f = 400 MHz.It will be good as a class B symmetric output stage driver. Delivery time was 60 days.

Verwenden Sie vor dem Anschluss Silikonfett unter den Transistoren. Die maximale Spannung beträgt 12 V. Die Transistoren arbeiten in der Klasse A. Bei 12 V beträgt der Strom 0,45 A. 1,25 W Ausgangsleistung, 27 dB Leistungsverstärkung bei f = 400 MHz. Er eignet sich als symmetrischer Endstufe-Treiber der Klasse B. Die Lieferzeit betrug 60 Tage.

Guter Wert... kann aber modifiziert werden, um besser zu arbeiten, indem der Bias-Strom auf der Ausgangsstufe. Widerstand R6 muss reduziert werden. Kann einen kleinen (10k) Trimpot, um einstellbar zu machen.

Good value... but can be modified to work better by reducing the bias current on the output stage. Resistor R6 needs to be reduced. Can use a small (10k) trimpot to make adjustable.

Guter Wert... kann aber modifiziert werden, um besser zu arbeiten, indem der Bias-Strom auf der Ausgangsstufe. Widerstand R6 muss reduziert werden. Kann einen kleinen (10k) Trimpot, um einstellbar zu machen.

Sehr gut

Very good

Sehr gut

Nice & functional. Some frequency output is 2F.

Nice & functional. Some frequency output is 2F.

Nice & functional. Some frequency output is 2F.

winzig, aber gut!

tiny but good!

winzig, aber gut!

Funktioniert gut mit einer Versorgungsspannung von nicht mehr als 10 Volt 100ma. Eingebaut in einem Metallgehäuse, mit einer Öffnung, durch die sich die Kühlrippen kreuzen.

Werkt goed bij een voedingsspanning niet hoger dan 10 volt 100ma. Ingebouwd in een metalen behuizing, met een opening waar de koelvinnen doorheen steken.

Funktioniert gut mit einer Versorgungsspannung von nicht mehr als 10 Volt 100ma. Eingebaut in einem Metallgehäuse, mit einer Öffnung, durch die sich die Kühlrippen kreuzen.

Hochgefahren auf 15,03 VDC wie angegeben und übertragen. Es frisiert in 10 Sekunden. Ich schlage vor, nur 12,0 VDC NO MEHR. Erwartung neuer Ordnung.

Powered up on 15.03 VDC as specified and transmitted. It fried in 10 seconds. I suggest using only 12.0 VDC NO MORE. Awaiting new order.

Hochgefahren auf 15,03 VDC wie angegeben und übertragen. Es frisiert in 10 Sekunden. Ich schlage vor, nur 12,0 VDC NO MEHR. Erwartung neuer Ordnung.

Haven't yet tried it...but all other things I ordered all worked fine. So no fear that this one won't work. And great quality for such a price. I use it for all kind of experiments.

Haven't yet tried it...but all other things I ordered all worked fine. So no fear that this one won't work. And great quality for such a price. I use it for all kind of experiments.

Haven't yet tried it...but all other things I ordered all worked fine. So no fear that this one won't work. And great quality for such a price. I use it for all kind of experiments.